Installation of 1. high pressure air booster pump

空气增压阀标配有两个开槽安装支架，增压阀可以安装在任意位置，推荐位置为垂直方向，每台售出增压阀都会附带图纸，标注所需的各种尺寸。

The air booster valve is equipped with two slotted mounting brackets, the booster valve can be installed at any position, the recommended position is vertical, each booster valve will be attached with the drawings, marking all the required sizes.

2.预增气源连接

2. yejiyuzeng source connection

高压空气增压泵泵体上都标注“进口”，且图纸上都标有端口尺寸及型号。预增气体一定要纯净，气体介质若有杂志可能会损坏高压元件，导致增压阀运行故障，所以建议大家在增压阀进气口安装过滤装置。

High pressure air booster pump body is marked "import", and the drawings are marked with port size and type. The pre - added gas must be pure. If there is a magazine in the gas medium that may damage the high pressure components and cause the operation failure of the pressurized valve, it is suggested that you install the filter in the air inlet of the pressurized valve.

3.气源的连接

Connection of 3. gas sources

供气回路的安装时过滤/调压阀需尽量开进增压阀。进气口端口为G1/4”，阀体上标注为”驱动气口“，管径为1/2”，如果管径较小，增压阀就不可以以较大流量运行。过滤调压需按照名称顺序链接，靠近增压阀。

When the gas supply circuit is installed, the filter / pressure regulating valve should be pushed into the booster valve as far as possible. The inlet port is G1/4 "and the valve body is marked as" driving air inlet ". The pipe diameter is 1/2". If the pipe diameter is small, the pressurized valve can not run with the maximum flow. Filtering and voltage regulation should be linked in name sequence, close to the booster valve.

4.消声器

4. muffler

消声器的使用时用来降低增压阀运行时的噪音，保证运行环境的安静。排气口端口为G1/2”，标记为“出气口”。

The muffler is used to reduce the noise of the booster valve and ensure the quietness of the running environment. The port of the exhaust port is G1/2, marked as "air outlet".

5.高压气体出口的连接

5. connection of high pressure gas outlet

在增压阀的配图上标有端口尺寸及型号，增压阀阀体上标注为“出口”，此为高压出口，所以连接时需要特别谨慎小心，连接件需要大于较大输出压力。

The size and model of the turbocharger valve are marked with the size and size of the port, and the valve body is marked as "exit". This is the high pressure outlet, so the connection needs to be careful and careful. The connector needs to be greater than the maximum output pressure.

6.高压空气增压泵的启动

The start of 6. high pressure air booster pump

⑴在打开增压阀的进气开关之前，使用调节减压阀将气压调到“0”PSI

In the switch before the intake pressure valve, regulating valve pressure will be transferred to the "0" PSI

⑵确保所有的连接口及所有元件及安装。

The connection port and ensure all all the components and installation.

⑶将减压阀缓慢调节至增压阀开始启动，正常情况下增压阀在15-20PSI压力下气动。

The valve will slowly adjust to the pressure valve is started, under normal circumstances, the pressure valve under the pressure of 15-20PSI pneumatic.

⑷完成1到3步骤后，调节泵的供气气压直达到系统所需输出压力为止。

The completion of the 1 to 3 steps, gas pressure regulating pump system to direct the desired output pressure.